The Structure and Syntax of the CadEnhance Symbol Description Language (SDL) is described here
Symbol Description Language Structure
The Symbol Description Language (SDL) was designed to be uber-efficient at describing schematic symbol construction, while still being simple to understand and easy to enter.
SDL KEY_WORDS and Constructs are Not case-sensitive.
An SDL File is a collection of ordered SYMBOL_NAME_DEFINITIONS which enclose MATCH_STATEMENTS and SPACER_COMMANDS.
The number of symbols you create is generally greater than or equal to the number of SYMBOL_NAME_DEFINITIONS.
Moving pins from one symbol to another is generally a cut and paste operation to move MATCH_STATEMENTS in between a different SYMBOL_NAME_DEFINTION.
To add another symbol, you just add another SYMBOL_NAME_DEFINTION with a new name and add or move your MATCH_STATEMENTS between the start and end.
SYMBOL_NAME_DEFINITIONS, MATCH_STATEMENTS and SPACER_COMMANDS can also appear between the start and end of LOOP_DIRECTIVES
SDL also supports Simple VARIABLE_SUBSTITUTION commands.
SYMBOL_NAME_DEFINITION
A SYMBOL_NAME_DEFINITION is used to instruct partBuilder to start placing matching pins into a named symbol.
It has 2 parts, a beginning:
SymbolName=
and an end which is just the terminating semicolon.
';'
The SymbolName is the actual name you want to use for the symbol and it should not contain spaces
in the simple sample file, the start of the first SYMBOL_NAME_DEFINITION was
DRAM_ACTL_PINS=
That was followed by several MATCH_STATEMENTS
and was terminated by the
';'
character
It instructed partBuilder to create a Symbol named DRAM_ACTL_PINS as a place to add the pins matching all the MATCH_STATEMENTS that follow until the SYMBOL_NAME_DEFINITION is closed.
A SYMBOL_NAME_STATEMENT may often create more than one symbol if the number of pins that the MATCH_STATEMENTS assign to that symbol are greater than the current Configuration Setting of the SYMBOL_PIN_LIMIT. For instance, a GROUND symbol definition often contains only one MATCH_STATEMENT to assign any pin matching GND to that symbol. If the part has 400 Ground pins and the SYMBOL_PIN_LIMIT is set to 100, it will create 4 SYMBOLS and create a new name for each of the extra symbols it creates (GROUND, GROUND_1, GROUND_2 and GROUND_3)
MATCH_STATEMENTS
MATCH_STATEMENTS are what tell partBuilder which pins to place within the current symbol, what side to place them on and any other modifier to enable creating special graphics or properites for the pins that match.
MATCH_STATEMENTS are built out of LOCATOR, MODIFIER and PIN_MATCH elements
The simplest MATCH_STATEMENT only contains a LOCATOR and a PIN_MATCH, and is entered as
LOCATOR=>PIN_MATCH or LOCATOR>>PIN_MATCH
The equal-Arrow "=>" or double-Arrow (recently added for easier entry in excel) separates the PIN_MATCH from the list of LOCATORS and MODIFIERS
MODIFIERS are added on the left hand side of the '=>' or '>>' either before or after the LOCATOR.
For clarity and easier cut and paste in Excel, our examples will show the LOCATOR first.
MODIFIERS and LOCATORS are separated by the colon character ':' as follows;
LOCATOR:MODIFIER1:MODIFIER2:...MODIFIERn=>PIN_MATCH
There is no restriction on the number of valid MODIFIERS that can be included in a MATCH_STATEMENT.
Only one LOCATOR is used per MATCH_STATEMENT
Some simple MATCH_STATEMENTS are provided in the table below to help get a feel for what they look like as you read more about the structure of them.
Examples of Simple MATCH_STATEMENTS
| MATCH_STATEMENT | Simple Operation* | Notes |
|---|---|---|
| left=>a[15:0] | puts bus pins a15...a0 on the left hand side of the symbol starting from the current position on the left hand side | |
right:dpair>>clk_p | puts diff_pair mates clk_p and clk_n** consecutively on the right hand side of the symbol using the currently configured defaults for diff pair spacing | **presumably clk_n showing double-arrow equivalence to => |
| top:is_pin=>1..17 | places pins 1 to pin 17 on the top of the symbol | |
| bot:bubble>>reset_n | places pin matching reset_n on the bottom and puts an inversion bubble between the pin and the symbol | showing double-arrow equivalence to => |
LOCATOR Elements
The purpose of the LOCATOR element is to tell partBuilder what side of the symbol to place the matching pins on.
Valid Locators are mostly obvious, and are explained in the following table
| LOCATOR | Effect |
|---|---|
| LEFT | place matching pins on the Left Hand Side of the symbol |
| RIGHT | place matching pins on the Right Hand Side of the symbol |
| BOTH | distribute the matching pins equally on the Left and Right Hand sides of the symbol |
| TOP | place matching pins on the top side of the symbol |
| BOT or BOTTOM | place matching pins on the bottom side of the symbol |
| AUTO | place matching INPUT pins on the Left Hand Side of the symbol place matching OUTPUT or INOUT pins on the Right Hand Side of the symbol distribute all other pin_types equally on the Left and Right Hand Sides of the symbol |
If the LOCATOR is not provided, it implies AUTO. This is not recommended going forward, but many older SDL files were written without LOCATORS.
MODIFIER Elements
Valid Modifiers are explained in the following table. Modifiers may be further broken down by partBuilder to impart extra information as shown
| MODIFIER | Effect | Special Notes |
|---|---|---|
| DOT or BUBBLE | Instructs PartBuilder to Add an Inversion Bubble in the proper place for any matching pin | |
| CLK or CLOCK | Instructs PartBuilder to Add a clock indicator like '>' in the proper place for any matching pin | |
| SHORT | Instructs PartBuilder to create a SHORT Pin | works for Eagle and Orcad Symbols |
| ZERO | Instructs PartBuilder ORCAD zero Length Pins | |
| HIDDEN | Instructs partBuilder to create a Hidden Pin. | This currently only works with AllegroHDL and is not reccomended |
| VECTOR or VECTORED | Instructs PartBuilder to create one symbol pin to represent 2 or more pins. | This currently only works with AllegroHDL and can be used to significantly reduce the size of power symbols |
| IS_PIN | Instructs PartBuilder that the PIN_MATCH should be applied to the Pin Number instead of the Pin Name | This makes it very easy to build parts where you layout the pins like they appear on the physical symbol. Also very efficient when building connectors organized by row or column |
DPAIR DPAIR_{OPT_SUFFIX} | Instructs PartBuilder to place both the matching diff_pair pin AND its mate pin in sequence | The DPAIR Modifier can be appended with a suffix to impart more information to override the default diff_pair spacing that is configured for partBuilder. |
| PSG_{swapGroupName} | Instructs PartBuilder that the matching pins are a member of a PIN_SWAP_GROUP. PartBuilder maintains a list of all the PIN_SWAP group names and properly annotates the matching pins so they can be included in the PIN_SWAP in the PCB side. | The name of the pinSwapGroup must be provided in the suffix to the PSG_ modifier. This is currently supported for AllegroHDL |
| BEST | Instructs PartBuilder that this Match should be accepted without going through the longest match algorithm | see Description of BEST Modifier below |
| IF_LAST_MATCH | This modifier is added to SPACER_COMMANDS within loops to avoid adding unnecessary spaces. | see Description of IS_LAST_MATCH modifier below |
| NO_WARN | PartBuilder will not print a warning for any PIN_MATCH with no matching pins if this modifier is applied | PartBuilder normally prints a warning for any PIN_MATCH in the SDL for which no pins were found. This can get very noisy in FPGAs where we allow many PIN_MATCHES to be empty. |
| EXACT | Treat the PIN_MATCH as an exact match. | to match the PIN_NAME must EQUAL the PIN_MATCH (if EXACT is not specified, the PIN_NAME must Contain the PIN_MATCH) This can be used to work around rare corner-cases that might have be fixed in another release of the tool |
| PIN_SPACE_{NUM_SPACES} | The PIN_SPACE modifier allows the user to specify extra spacing when adding the pins that match the PIN_MATCH statement. PIN_SPACE_1 tells part builder to add 1 extra spacer between each added pin. | This command is very helpful if the user wants to add power pins or a full bus with extra spacing between the individual pins, but they don't want to change the global spacing grid for all the other pins. |
PIN_MATCH Elements
The PIN_MATCH Element is the string that PartBuilder uses to test all pins in the extracted pinData for a match.
PIN_MATCHES may be entered as a simple string or with a wildcard.
PartBuilder treats all the PIN_MATCHES it extracts from the SDL as a Regular Expression. It actually converts the wildcard '*' internally to the '.*' used in Regular Expressions.
They may also be entered as a valid Perl Regular Expression.
PartBuilder treats all the PIN_MATCHES it extracts from the SDL as a Regular Expression. It actually converts the wildcard '*' internally to the '.*' used in Regular Expressions.
A Regular Expression is a pattern describing a certain amount of Text. The Regular Expression can be very general or very restrictive.
In the simplest context, PartBuilder uses a regular expressions to determine if a Pin contains the PIN_MATCH pattern.
If the PIN_MATCH is entered as "DQ", PartBuilder will match any pin that Contains DQ anywhere in the pinname.
Excellent references for Regular Expressions exist on the web like the one at this link.
PartBuilder Bus-Enhanced Regular Expressions.
PartBuilder does some behind the scenes work to change the PIN_MATCH Regular Expressions to enable placing bussed pins seamlessly
Its not truly necessary to understand this detail, but In a normal regular expression, the '[]' characters in the pattern match enclose a list of characters to match against
If you were comparing a list of pins dq7 dq6 dq5 dq4 dq3 dq2 dq1 and dq0 using the regular Expression 'dq[0:7]' , the pattern would only match dq0 and dq7 (and funny enough dq:).
You could get more useful results with 'dq[0-7]' (because 0-7 inside the square brackets says to match any character between 0 and 7) but unfortunately that would not enforce the order of the pins.
To work around this issue, when PartBuilder sees the 'DQ[0:7]' in a PIN_MATCH it expands it to 8 separate PIN_MATCHES DQ0, DQ1, DQ2... DQ7** which are then used as pattern matches.
It also maintains the order of the bits so that they will be added to the symbol in LSB→MSB order if you enter busName[0:7] or MSB→LSB order if you enter busName[7:0]. As described in the table below, it also appends whats called a zero-width-lookahead assertion at the end fo each to insure that DQ18 doesn't match DQ1 but it would still allow a match of dq1_p
(**it also appends a zero-width-lookahead assertion to each match to ensure that no other digits are following the ones we want so that DQ18 doesn't match DQ1)
Examples of Useful PIN_MATCH Regular Expressions
| PIN_MATCH | Effect | NOTES |
|---|---|---|
| DQ | Will match any pin that contains DQ | |
| DQS | Will match any pin that contains DQS | |
| ^DQS0 | Will match any pin that STARTS with DQS0 | the caret '^' enforces the start of word boundary |
| DQ[7:0] | PartBuilder will expand this to 8 individual matches DQ7, DQ6, DQ5... DQ0** it will match and maintain the order of any pins that contain any of those patterns DQ7, DRAM_DQ6_BUS, DQ5_F would all match DQA7, DQ06... would not match DQ3_P and DQ1_N would match but DQ31_P and DQ18_N would not | In the category of too much information: DQ18_N seems like it should match because it contains DQ1, but when partBuilder expands the PIN_MATCH it also adds what is called a zero-width look-ahead assertion to the regular expression. This ensures that the pattern will not match if there is a another digit immediately following the last digit. |
| ^DQ[0:7] | PartBuilder will match any pin that STARTS with DQ0 or DQ1... DQ7 L_DQ0 would not match | |
| DQ[0:7]$ | PartBuilder will match any pin that ENDS with DQ0 or DQ1 ... DQ7 DQ0_L would not match since it doesn't end with 0,1,2,3,,4,5,6,or 7 | the dollar Sign '$' enforces the end of word boundary |
| ^DQ[0:7]$ | PartBuilder will expand to a list of matches ^DQ0$, ^DQ1$, ^DQ2$... ^DQ7$ and will only match DQ0,DQ1,DQ2,DQ3...DQ7... Would not match L_DQ0, DQ00, DQ01 ..... | The caret '^' says it must start with the D and the $ says it must end with the digit at the end |
IO_.*?_35 or IO_*_35 | PartBuilder will match any pin that contains IO_, and _35 it would match: IO__35, IO_A_35, IO1_PIN1_35, IO_THIS_IS_A_LONG_NAME_35 it would not match IO_A_36, IO_A_37 nor would it match IO35 or IO_35 (since we need 2 underscores) | the '.*?' (which could also be be entered as '*') looks for any number of any of characters partBuilder converts the '*' to a '.*?' to make it easier to enter wildcards for those not familiar with Regular Expressions. The ? is special and necessary because it makes the match stop if it sees the _35 after it. This particular regular Expression is very powerful when building parts with Pins that have similar names grouped into numeric banks like FPGAs and CPLDS. |
| IO\d+_\d+ | Would match: IO0_5, IO7324_8910 Would not match: IO0A_5 because it is not looking for the 'A' or IO_5 because we need a digit after the IO | the \d+ finds 1 or more consecutive digits in a row. if we used "IO\d*_\d+", it would match IO_5 because \d* says find 0 or more consecutive digits. |
Assigning Pins that match multiple MATCH_STATEMENTS
It takes PartBuilder 2 passes to place matching pins into the proper symbols. It first goes through every pin_match and attaches a list of every MATCH_STATEMENT that each pin matches to the pin. It then makes a second pass, and chooses the MATCH_STATEMENT with the longest PIN_MATCH string to pick the proper MATCH_STATEMENT for that pin.
Lets provide a simple example:
We are building a part that has 100 pins named GND, 8 pins named AGND and 2 pins named GTH_RX_AGND and 2 named GTH_TX_AGND
We have the following 2 SYMBOL_NAME_DEFINITIONS in the SDL File
GND_SYM= LEFT=>AGND LEFT=>SPACER[1:0] BOTH=>GND ; |
|
GTH_BLOCK= LEFT:dpair=>GTH_RX[7:0]_P RIGHT:dpair=>GTH_RX[7:0]_N !BSS+2 LEFT=>GTH_RX_AGND RIGHT=>GTH_TX_AGND ; |
Because of this 2 pass approach, the user does not need to concern themselves with what order a MATCH_STATEMENT is placed or what SYMBOL_DEFINITION it is placed in.
They should be aware that the 2 pass approach is necessary and that they need to assign more specific PIN_MATCHES if they want to separate Pins like the example that have common strings in them
The BEST Modifier in pin matching
In some odd cases (mostly when using loops and variables), The longest match might place a pin where you don't want it to.
SDL provides the BEST modifier to allow you to work around these cases.
Lets say we have an FPGA with a bunch of pins in bank 37 that we are trying to order using a bus so we use
left=>IO_L[19:0]*_37
but there is a pin in that bank named IO_L4_VREF_37, which we want to place in a different symbol (or somewhere in the same symbol)
if we use the BEST modifier,
left:BEST=>VREF_37
we guarantee that this match will claim the signal matching VREF_37, and not the longer IO_L4*_37 match.
SPACER_COMMANDS
SPACER_COMMANDS allow the user to easily control spacing between groups of pins
There are 3 types:
- SINGLE_SPACERS:
- LOCATOR=>SPACER,
- MULTIPLE_SPACERS:
- LOCATOR=>SPACER[5:0]
- and SPACER_DIRECTIVES:
- !BALANCE_SYM_SIDES+n (or !BSS+n)
The first 2 resemble the MATCH_STATEMENTS pretty closely and use the LEFT, RIGHT, TOP and BOTTOM LOCATOR commands.
The !BALANCE_SYM_SIDES directive is used to start a new section in the same symbol without having to keep track of the number of pins you have been adding on the sides of your symbols.
For instance if you have 3 pins on the left and 8 pins on the right, The BALANCE_SYM_SIDES+2 directive would add 5 spacer pins on the left to Balance it with the right side, and then add 2 more spacers on each side.
l_spacer, r_spacer shorthand
**Older SDL files used the short-hand
l_spacer for LEFT=>spacer
and
r_spacer for RIGHT=>spacer.
The shorthand is still available but it is not as convienient for cut and paste in the spreadsheet format.
IF_LAST_MATCH modifier for SPACER_COMMANDS
It is very convenient to use loops with ranges of FPGA bank numbers where some of the bank numbers might not exist. In that loop you would normally place a spacer command to separate the banks. In the normal case, those spacers will always be added even if a bank doesn't exist. The IF_LAST_MATCH modifier can be used to avoid placing unwanted spacers when there are no matched signals between consecutive SPACER_COMMANDS
for instance if you have an FPGA that only contains IO banks 12,13,15,17. (another FPGA in the family could have IO banks 12,13,14,15,16,and 17
You use a loop:
`for b in (12..17) left=>io.*_`b:: left=>spacer[1:0] `endfor
which expands to
left=>io.*_12 left=>spacer[1:0] left=>io.*_13 left=>spacer[1:0] left=>io.*_14 left=>spacer[1:0] left=>io.*_15 left=>spacer[1:0] left=>io.*_16 left=>spacer[1:0] left=>io.*_17 left=>spacer[1:0]
But for this FPGA , there will be no pins that match IO.*_14 or IO.*_16.
If the spacer is unmodified you will get 4 spacers between the IO.*_13 pins and the IO.*_15 pins, and 4 between the IO.*_15 and IO.*_17 pins.
if you add the IF_LAST_MATCH modifier as follows
`for b in (12..17) left=>io.*_`b:: left:IF_LAST_MATCH=>spacer[1:0] `endfor
left=>io.*_12 left:IF_LAST_MATCH=>spacer[1:0] left=>io.*_13 left:IF_LAST_MATCH=>spacer[1:0] left=>io.*_14 left:IF_LAST_MATCH=>spacer[1:0] left=>io.*_15 left:IF_LAST_MATCH=>spacer[1:0] left=>io.*_16 left:IF_LAST_MATCH=>spacer[1:0] left=>io.*_17 left:IF_LAST_MATCH=>spacer[1:0]
With the IF_LAST_MATCH PartBuilder will not add the spacers if it did not see any matching pins between the last occurrence of a spacer and the next one.
so IO_.*13 will match some pins, so the left:IF_LAST_MATCH=>spacer[1:0] will be honored, then partbuilder will clear the match count, it will look at the io.*_14 match and see no pins.. When it gets to the next IF_LAST_MATCH=>spacer[1:0] command, it will not add those spacers.
GRID_ADJUST
Support for a new
LOCATOR=>!GRID_ADJUST_{fractional_space_specifier}
Command was added in version v18.5.5 to allow partBuilder to move pins off grid to let Smart-Frac exactly match pin locations from previously created symbols.
Normally pins are always added in whole grid increments, but to match pre-existing symbol pin placements it may be necessary to move a pin onto a half grid space
For example:
LEFT=>!GRID_ADJUST_0.5 will move the next pin 0.5 grid spaces so that all the next pins will start on the half grid space (until another !GRID_ADJUST command would be used to move pins back onto the whole grid)
Add Comment